Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Fayetteville Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco service in Fayetteville: sweeping, cap replacement, and damper repair on Gelco-lined flues, Gelco caps, and Gelco top-sealing damper assemblies. What makes our Gelco work different is that we’re not tied to the brand, so the conversation stays on what your flue and firebox actually need instead of a sales push toward a new system. We’re an independent service provider, not authorized by or affiliated with Gelco, and we say that up front because it matters to how we advise you.
Fayetteville’s chimney stock makes that independence useful. Most of the housing here is post-1950 ranches, split-levels, and builder-grade two-story subdivisions across Fayetteville, Hope Mills, and Spring Lake, plus older brick and wood-frame homes in Haymount and downtown. Many of those chimneys carry original clay tile liners, and plenty of them have been retrofitted with flexible stainless systems over the years. Some of that retrofit work is good. Some of it isn’t.
We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (855) 608-7738.
Why Trust Delmar Chimney Sweep for Your Gelco Chimney Cleaning?
Our technicians have up to experience, and a good share of that has been spent inside flues with flexible stainless liners, caps, and top-sealing dampers in place. That matters more than it sounds. A Gelco installation changes how a flue gets swept, what a camera sees, and where debris collects. Technicians who mostly work open masonry fireplaces miss those details.
We service Gelco equipment with quality parts that fit it, sourced from professional chimney supply brands rather than whatever’s cheapest on a hardware store shelf. We don’t claim to stock OEM or genuine Gelco parts, and we’re not a Gelco dealer. What we do is fit the right liner, cap, damper, or gasket to the system that’s already on your chimney and make sure it seals and drafts the way it should.
Every job is scoped so it doesn’t void your manufacturer warranty. That means no cutting corners on a liner that’s still serviceable, no forcing a cap that doesn’t match the flue opening, and no sealant where a proper gasket belongs. If a part fails because of how it was installed, we want that on record as our problem, not yours.
One company handles the sweep, the repair, and the inspection. No finger-pointing between contractors when something doesn’t line up.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Fayetteville
Fayetteville’s humid subtropical climate is hard on chimney components. Long humid summers, mild winters, and frequent heavy rain mean flues sit idle for months, then get fired hard during short cold snaps. That pattern produces a predictable set of Gelco problems.
- Kinked or crushed flexible liner sections at flue offsets. Flexible stainless has to bend around an offset, and if it bends too tight during installation it pinches. The liner still passes flue gas, so nothing seems wrong at first. Then draft weakens, creosote collects at the pinch point, and smoke starts rolling back into the room. The kink is almost always at the offset, not at the top or bottom.
- Top-sealing damper gaskets that dry out and warp. The gasket is what makes a top-sealing damper seal. Carolina summers dry the rubber out, and by the time cold weather arrives the damper closes but doesn’t seal. Cold air pours down the flue, rain finds its way in, and the fireplace feels like it’s fighting you every time you light it.
- Caps with mesh or louvers clogged by soot and nesting debris. A cap that’s breathing properly keeps rain and animals out while letting exhaust through. When the mesh loads up with soot and nest material, exhaust flow drops, draft suffers, and the cap starts acting more like a plug than a vent.
- Liner-to-appliance collar connections that loosen on inserts. Where the liner meets an insert or firebox collar, vibration and heat cycles work the connection loose. Smoke spills around the surround instead of going up the flue, and creosote builds in the void behind it where nobody looks until there’s a problem.
- Washed-out mortar and cracked crowns letting water into the system. Brick chimneys on Haymount-era houses often show this after decades of rain. A cracked crown doesn’t just look bad, it lets water run down into the flue and around the liner, which shortens the life of everything inside.
Gelco Parts & Our Repair-vs-Replace Approach
Gelco-compatible liners, caps, dampers, and gaskets are available from quality aftermarket suppliers, and for most repairs that’s the practical route. Where a specific fit matters, an OEM part can make more sense, and we’ll say so when it does. We don’t stock either one, so there’s no pressure to make what’s on hand fit the job.
The repair-versus-replace call is where independence earns its keep. A liner that’s crushed at an offset or deteriorated past the point of a safe sweep doesn’t get better with another cleaning. Repeating sweeps on a failing flue just delays the honest answer. When the camera shows a liner that can’t be safely cleaned, we’ll tell you it needs relining and show you why.
The reverse is just as true. Plenty of Gelco systems get flagged for replacement by dealer-affiliated techs when a gasket or a cap would solve the actual problem. If a repair will get you years of safe service, that’s the recommendation.
Call (855) 608-7738 and we’ll talk through what you’re seeing before anyone quotes anything.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We sweep the flue first, then run a camera to look at the liner’s interior. For Gelco flexible systems, we’re checking the bends at every offset for kinks, and checking that the liner hasn’t shifted at the collar or top plate. For a top-sealing damper, we check the gasket and the seal face. Photos go into the report.
- 2
Repair or install. Depending on what the camera shows, that means reseating or replacing a damper gasket, replacing a clogged or corroded cap with a properly sized unit, tightening and sealing a loose collar connection, or, where the liner is crushed beyond safe use, recommending relining.
- 3
Test. We verify draft with the damper closed and open, confirm the cap seals against rain without blocking exhaust, and check that an insert’s collar connection is tight with no spillage at the surround.
- 4
Warranty-safe close-out. You get a written record of what was done and what it looked like before and after. If any part was replaced, the documentation identifies it so your warranty stays intact.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Fayetteville
We work on the Gelco components Fayetteville homeowners actually have on their chimneys: stainless-steel flexible chimney liner kits, chimney caps and multi-flue caps, top-sealing damper assemblies, and fireplace inserts with their gas fireplace components. Sweeping a Gelco-lined flue is different from sweeping bare masonry, because the liner surface and the bends at offsets change where creosote collects and how the brush passes. Cap replacement and damper repair are the two calls we make most often on Gelco systems, especially on Fayetteville chimneys that sit unused through the humid summer and then get worked hard in January. If you’re not sure which component is causing your problem, that’s what the camera inspection settles.
We Also Service These Brands
Gelco is one brand in a wider field, and we service the others too. We install DuraFlex flexible liner systems for retrofits on older or offset chimneys where rigid liners won’t fit. We use HeatShield ceramic resurfacing to restore damaged flues without a full reliner tear-out. If your chimney carries a different make of liner, cap, or damper, call and describe it. We’ll tell you honestly whether it’s something we handle.
FAQs – Gelco Chimney Cleaning Service in Fayetteville
No. We’re an independent Gelco service provider, not authorized, certified, or affiliated with the manufacturer. That independence is deliberate: our recommendations follow what the flue and firebox need, not what a brand relationship rewards.
Yes. We fit Gelco-compatible liners, caps, dampers, and gaskets sourced from professional chimney supply brands. We don’t stock OEM or genuine Gelco parts and we’re not a dealer, but we know which aftermarket components fit properly and which ones fail early. Where a specific fit calls for OEM, we’ll tell you.
Most Gelco sweeps and inspections take under two hours. Cap replacement or damper gasket work usually adds less than an hour. A reline takes longer, typically most of a day, and we scope that in the written estimate before any work starts. Call (855) 608-7738 for an exact quote; estimates are free.
Stainless-steel flexible liner kits, chimney caps and multi-flue caps, top-sealing damper assemblies, and fireplace inserts with gas fireplace components. If your Gelco setup isn’t on that list, call and describe it. We’ll say plainly whether it’s in scope.
Not when it’s done correctly. We follow warranty-safe practices: proper gasket sealing, correct cap sizing, documented sweep and inspection records. What can void a warranty is a repair done with the wrong part or a liner that was damaged during a bad installation. We check for that.
A typical sweep in the Fayetteville area runs roughly $150 to $300, and an inspection with a camera report usually lands in the $175 to $350 range. Damper gasket work and cap replacement are quoted separately once we know the size and style. The written estimate sets the final price, and there’s no charge for the estimate itself. Call (855) 608-7738 for an exact quote; estimates are free.
A kinked liner can sometimes be swept, but the kink itself doesn’t clean up. If the pinch point is trapping creosote and restricting draft, repeated sweeps just delay the honest answer, which is usually relining. A camera inspection tells you which situation you’re in before you spend anything.
Almost always a gasket. The rubber dries out and warps over Carolina summers, so the damper closes but doesn’t seal. Replacing the gasket solves it in most cases; if the seal face itself is damaged, the assembly may need more work.
Clean it if the mesh and louvers are still sound. Replace it if the mesh is corroded through or the louvers are bent, because a cleaning won’t restore airflow. In Fayetteville, caps that sit through a humid summer with nesting debris tend to corrode faster. Call (855) 608-7738 and we’ll tell you which call fits what you’re seeing.
Yes. An insert’s firebox is closed, so soot and creosote don’t behave the same way, and the liner-to-collar connection behind the surround needs checking. We sweep insert flues with that in mind and photograph the collar area so you can see the connection yourself.
Once a year for most households, and more often if you burn hard through the winter. What Fayetteville’s climate adds is the summer side: a flue that sits idle through humid months collects moisture and nests even if you barely burn. A yearly sweep and a camera look catch both problems.
Book Your Gelco Service in Fayetteville, NC
Whether you need a routine sweep on a Gelco-lined flue, a cap replacement, or a damper repair before cold weather arrives, we’ll sweep first, assess honestly, and recommend a repair only when the camera shows one is needed. Call (855) 608-7738 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Delmar Chimney Sweep.